In the Linux kernel, the following vulnerability has been resolved: rxrpc: fix oversized RESPONSE authenticator length check rxgk_verify_response() decodes auth_len from the packet and is supposed to verify that it fits in the remaining bytes. The existing check is inverted, so oversized RESPONSE authenticators are accepted and passed to rxgk_decrypt_skb(), which can later reach skb_to_sgvec() with an impossible length and hit BUG_ON(len). Decoded from the original latest-net reproduction logs with scripts/decode_stacktrace.sh: RIP: __skb_to_sgvec() [net/core/skbuff.c:5285 (discriminator 1)] Call Trace: skb_to_sgvec() [net/core/skbuff.c:5305] rxgk_decrypt_skb() [net/rxrpc/rxgk_common.h:81] rxgk_verify_response() [net/rxrpc/rxgk.c:1268] rxrpc_process_connection() [net/rxrpc/conn_event.c:266 net/rxrpc/conn_event.c:364 net/rxrpc/conn_event.c:386] process_one_work() [kernel/workqueue.c:3281] worker_thread() [kernel/workqueue.c:3353 kernel/workqueue.c:3440] kthread() [kernel/kthread.c:436] ret_from_fork() [arch/x86/kernel/process.c:164] Reject authenticator lengths that exceed the remaining packet payload.

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix use of wrong skb when comparing queued RESP challenge serial In rxrpc_post_response(), the code should be comparing the challenge serial number from the cached response before deciding to switch to a newer response, but looks at the newer packet private data instead, rendering the comparison always false. Fix this by switching to look at the older packet. Fix further[1] to substitute the new packet in place of the old one if newer and also to release whichever we don't use.

In the Linux kernel, the following vulnerability has been resolved: net/rds: Fix circular locking dependency in rds_tcp_tune syzbot reported a circular locking dependency in rds_tcp_tune() where sk_net_refcnt_upgrade() is called while holding the socket lock: ====================================================== WARNING: possible circular locking dependency detected ====================================================== kworker/u10:8/15040 is trying to acquire lock: ffffffff8e9aaf80 (fs_reclaim){+.+.}-{0:0}, at: __kmalloc_cache_noprof+0x4b/0x6f0 but task is already holding lock: ffff88805a3c1ce0 (k-sk_lock-AF_INET6){+.+.}-{0:0}, at: rds_tcp_tune+0xd7/0x930 The issue occurs because sk_net_refcnt_upgrade() performs memory allocation (via get_net_track() -> ref_tracker_alloc()) while the socket lock is held, creating a circular dependency with fs_reclaim. Fix this by moving sk_net_refcnt_upgrade() outside the socket lock critical section. This is safe because the fields modified by the sk_net_refcnt_upgrade() call (sk_net_refcnt, ns_tracker) are not accessed by any concurrent code path at this point. v2: - Corrected fixes tag - check patch line wrap nits - ai commentary nits

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix race condition during IPSec ESN update In IPSec full offload mode, the device reports an ESN (Extended Sequence Number) wrap event to the driver. The driver validates this event by querying the IPSec ASO and checking that the esn_event_arm field is 0x0, which indicates an event has occurred. After handling the event, the driver must re-arm the context by setting esn_event_arm back to 0x1. A race condition exists in this handling path. After validating the event, the driver calls mlx5_accel_esp_modify_xfrm() to update the kernel's xfrm state. This function temporarily releases and re-acquires the xfrm state lock. So, need to acknowledge the event first by setting esn_event_arm to 0x1. This prevents the driver from reprocessing the same ESN update if the hardware sends events for other reason. Since the next ESN update only occurs after nearly 2^31 packets are received, there's no risk of missing an update, as it will happen long after this handling has finished. Processing the event twice causes the ESN high-order bits (esn_msb) to be incremented incorrectly. The driver then programs the hardware with this invalid ESN state, which leads to anti-replay failures and a complete halt of IPSec traffic. Fix this by re-arming the ESN event immediately after it is validated, before calling mlx5_accel_esp_modify_xfrm(). This ensures that any spurious, duplicate events are correctly ignored, closing the race window.

In the Linux kernel, the following vulnerability has been resolved: bonding: prevent potential infinite loop in bond_header_parse() bond_header_parse() can loop if a stack of two bonding devices is setup, because skb->dev always points to the hierarchy top. Add new "const struct net_device *dev" parameter to (struct header_ops)->parse() method to make sure the recursion is bounded, and that the final leaf parse method is called.

In the Linux kernel, the following vulnerability has been resolved: net: ti: icssg-prueth: Fix memory leak in XDP_DROP for non-zero-copy mode Page recycling was removed from the XDP_DROP path in emac_run_xdp() to avoid conflicts with AF_XDP zero-copy mode, which uses xsk_buff_free() instead. However, this causes a memory leak when running XDP programs that drop packets in non-zero-copy mode (standard page pool mode). The pages are never returned to the page pool, leading to OOM conditions. Fix this by handling cleanup in the caller, emac_rx_packet(). When emac_run_xdp() returns ICSSG_XDP_CONSUMED for XDP_DROP, the caller now recycles the page back to the page pool. The zero-copy path, emac_rx_packet_zc() already handles cleanup correctly with xsk_buff_free().

In the Linux kernel, the following vulnerability has been resolved: tipc: fix bc_ackers underflow on duplicate GRP_ACK_MSG The GRP_ACK_MSG handler in tipc_group_proto_rcv() currently decrements bc_ackers on every inbound group ACK, even when the same member has already acknowledged the current broadcast round. Because bc_ackers is a u16, a duplicate ACK received after the last legitimate ACK wraps the counter to 65535. Once wrapped, tipc_group_bc_cong() keeps reporting congestion and later group broadcasts on the affected socket stay blocked until the group is recreated. Fix this by ignoring duplicate or stale ACKs before touching bc_acked or bc_ackers. This makes repeated GRP_ACK_MSG handling idempotent and prevents the underflow path.

In the Linux kernel, the following vulnerability has been resolved: nvme-tcp: fix NULL pointer dereferences in nvmet_tcp_build_pdu_iovec Commit efa56305908b ("nvmet-tcp: Fix a kernel panic when host sends an invalid H2C PDU length") added ttag bounds checking and data_offset validation in nvmet_tcp_handle_h2c_data_pdu(), but it did not validate whether the command's data structures (cmd->req.sg and cmd->iov) have been properly initialized before processing H2C_DATA PDUs. The nvmet_tcp_build_pdu_iovec() function dereferences these pointers without NULL checks. This can be triggered by sending H2C_DATA PDU immediately after the ICREQ/ICRESP handshake, before sending a CONNECT command or NVMe write command. Attack vectors that trigger NULL pointer dereferences: 1. H2C_DATA PDU sent before CONNECT → both pointers NULL 2. H2C_DATA PDU for READ command → cmd->req.sg allocated, cmd->iov NULL 3. H2C_DATA PDU for uninitialized command slot → both pointers NULL The fix validates both cmd->req.sg and cmd->iov before calling nvmet_tcp_build_pdu_iovec(). Both checks are required because: - Uninitialized commands: both NULL - READ commands: cmd->req.sg allocated, cmd->iov NULL - WRITE commands: both allocated

In the Linux kernel, the following vulnerability has been resolved: nvmet: fix race in nvmet_bio_done() leading to NULL pointer dereference There is a race condition in nvmet_bio_done() that can cause a NULL pointer dereference in blk_cgroup_bio_start(): 1. nvmet_bio_done() is called when a bio completes 2. nvmet_req_complete() is called, which invokes req->ops->queue_response(req) 3. The queue_response callback can re-queue and re-submit the same request 4. The re-submission reuses the same inline_bio from nvmet_req 5. Meanwhile, nvmet_req_bio_put() (called after nvmet_req_complete) invokes bio_uninit() for inline_bio, which sets bio->bi_blkg to NULL 6. The re-submitted bio enters submit_bio_noacct_nocheck() 7. blk_cgroup_bio_start() dereferences bio->bi_blkg, causing a crash: BUG: kernel NULL pointer dereference, address: 0000000000000028 #PF: supervisor read access in kernel mode RIP: 0010:blk_cgroup_bio_start+0x10/0xd0 Call Trace: submit_bio_noacct_nocheck+0x44/0x250 nvmet_bdev_execute_rw+0x254/0x370 [nvmet] process_one_work+0x193/0x3c0 worker_thread+0x281/0x3a0 Fix this by reordering nvmet_bio_done() to call nvmet_req_bio_put() BEFORE nvmet_req_complete(). This ensures the bio is cleaned up before the request can be re-submitted, preventing the race condition.

In the Linux kernel, the following vulnerability has been resolved: libceph: return the handler error from mon_handle_auth_done() Currently any error from ceph_auth_handle_reply_done() is propagated via finish_auth() but isn't returned from mon_handle_auth_done(). This results in higher layers learning that (despite the monitor considering us to be successfully authenticated) something went wrong in the authentication phase and reacting accordingly, but msgr2 still trying to proceed with establishing the session in the background. In the case of secure mode this can trigger a WARN in setup_crypto() and later lead to a NULL pointer dereference inside of prepare_auth_signature().

In the Linux kernel, the following vulnerability has been resolved: net: can: j1939: j1939_xtp_rx_rts_session_active(): deactivate session upon receiving the second rts Since j1939_session_deactivate_activate_next() in j1939_tp_rxtimer() is called only when the timer is enabled, we need to call j1939_session_deactivate_activate_next() if we cancelled the timer. Otherwise, refcount for j1939_session leaks, which will later appear as | unregister_netdevice: waiting for vcan0 to become free. Usage count = 2. problem.

In the Linux kernel, the following vulnerability has been resolved: RDMA/siw: Fix potential NULL pointer dereference in header processing If siw_get_hdr() returns -EINVAL before set_rx_fpdu_context(), qp->rx_fpdu can be NULL. The error path in siw_tcp_rx_data() dereferences qp->rx_fpdu->more_ddp_segs without checking, which may lead to a NULL pointer deref. Only check more_ddp_segs when rx_fpdu is present. KASAN splat: [ 101.384271] KASAN: null-ptr-deref in range [0x00000000000000c0-0x00000000000000c7] [ 101.385869] RIP: 0010:siw_tcp_rx_data+0x13ad/0x1e50

In the Linux kernel, the following vulnerability has been resolved: libceph: reset sparse-read state in osd_fault() When a fault occurs, the connection is abandoned, reestablished, and any pending operations are retried. The OSD client tracks the progress of a sparse-read reply using a separate state machine, largely independent of the messenger's state. If a connection is lost mid-payload or the sparse-read state machine returns an error, the sparse-read state is not reset. The OSD client will then interpret the beginning of a new reply as the continuation of the old one. If this makes the sparse-read machinery enter a failure state, it may never recover, producing loops like: libceph: [0] got 0 extents libceph: data len 142248331 != extent len 0 libceph: osd0 (1)...:6801 socket error on read libceph: data len 142248331 != extent len 0 libceph: osd0 (1)...:6801 socket error on read Therefore, reset the sparse-read state in osd_fault(), ensuring retries start from a clean state.

In the Linux kernel, the following vulnerability has been resolved: ip6_tunnel: use skb_vlan_inet_prepare() in __ip6_tnl_rcv() Blamed commit did not take care of VLAN encapsulations as spotted by syzbot [1]. Use skb_vlan_inet_prepare() instead of pskb_inet_may_pull(). [1] BUG: KMSAN: uninit-value in __INET_ECN_decapsulate include/net/inet_ecn.h:253 [inline] BUG: KMSAN: uninit-value in INET_ECN_decapsulate include/net/inet_ecn.h:275 [inline] BUG: KMSAN: uninit-value in IP6_ECN_decapsulate+0x7a8/0x1fa0 include/net/inet_ecn.h:321 __INET_ECN_decapsulate include/net/inet_ecn.h:253 [inline] INET_ECN_decapsulate include/net/inet_ecn.h:275 [inline] IP6_ECN_decapsulate+0x7a8/0x1fa0 include/net/inet_ecn.h:321 ip6ip6_dscp_ecn_decapsulate+0x16f/0x1b0 net/ipv6/ip6_tunnel.c:729 __ip6_tnl_rcv+0xed9/0x1b50 net/ipv6/ip6_tunnel.c:860 ip6_tnl_rcv+0xc3/0x100 net/ipv6/ip6_tunnel.c:903 gre_rcv+0x1529/0x1b90 net/ipv6/ip6_gre.c:-1 ip6_protocol_deliver_rcu+0x1c89/0x2c60 net/ipv6/ip6_input.c:438 ip6_input_finish+0x1f4/0x4a0 net/ipv6/ip6_input.c:489 NF_HOOK include/linux/netfilter.h:318 [inline] ip6_input+0x9c/0x330 net/ipv6/ip6_input.c:500 ip6_mc_input+0x7ca/0xc10 net/ipv6/ip6_input.c:590 dst_input include/net/dst.h:474 [inline] ip6_rcv_finish+0x958/0x990 net/ipv6/ip6_input.c:79 NF_HOOK include/linux/netfilter.h:318 [inline] ipv6_rcv+0xf1/0x3c0 net/ipv6/ip6_input.c:311 __netif_receive_skb_one_core net/core/dev.c:6139 [inline] __netif_receive_skb+0x1df/0xac0 net/core/dev.c:6252 netif_receive_skb_internal net/core/dev.c:6338 [inline] netif_receive_skb+0x57/0x630 net/core/dev.c:6397 tun_rx_batched+0x1df/0x980 drivers/net/tun.c:1485 tun_get_user+0x5c0e/0x6c60 drivers/net/tun.c:1953 tun_chr_write_iter+0x3e9/0x5c0 drivers/net/tun.c:1999 new_sync_write fs/read_write.c:593 [inline] vfs_write+0xbe2/0x15d0 fs/read_write.c:686 ksys_write fs/read_write.c:738 [inline] __do_sys_write fs/read_write.c:749 [inline] __se_sys_write fs/read_write.c:746 [inline] __x64_sys_write+0x1fb/0x4d0 fs/read_write.c:746 x64_sys_call+0x30ab/0x3e70 arch/x86/include/generated/asm/syscalls_64.h:2 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xd3/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was created at: slab_post_alloc_hook mm/slub.c:4960 [inline] slab_alloc_node mm/slub.c:5263 [inline] kmem_cache_alloc_node_noprof+0x9e7/0x17a0 mm/slub.c:5315 kmalloc_reserve+0x13c/0x4b0 net/core/skbuff.c:586 __alloc_skb+0x805/0x1040 net/core/skbuff.c:690 alloc_skb include/linux/skbuff.h:1383 [inline] alloc_skb_with_frags+0xc5/0xa60 net/core/skbuff.c:6712 sock_alloc_send_pskb+0xacc/0xc60 net/core/sock.c:2995 tun_alloc_skb drivers/net/tun.c:1461 [inline] tun_get_user+0x1142/0x6c60 drivers/net/tun.c:1794 tun_chr_write_iter+0x3e9/0x5c0 drivers/net/tun.c:1999 new_sync_write fs/read_write.c:593 [inline] vfs_write+0xbe2/0x15d0 fs/read_write.c:686 ksys_write fs/read_write.c:738 [inline] __do_sys_write fs/read_write.c:749 [inline] __se_sys_write fs/read_write.c:746 [inline] __x64_sys_write+0x1fb/0x4d0 fs/read_write.c:746 x64_sys_call+0x30ab/0x3e70 arch/x86/include/generated/asm/syscalls_64.h:2 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xd3/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f CPU: 0 UID: 0 PID: 6465 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(none) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_conncount: update last_gc only when GC has been performed Currently last_gc is being updated everytime a new connection is tracked, that means that it is updated even if a GC wasn't performed. With a sufficiently high packet rate, it is possible to always bypass the GC, causing the list to grow infinitely. Update the last_gc value only when a GC has been actually performed.

In the Linux kernel, the following vulnerability has been resolved: VFS: fix possible failure to unlock in nfsd4_create_file() atomic_create() in fs/namei.c drops the reference to the dentry when it returns an error. This behaviour was imported into dentry_create() so that it will drop the reference if an error is returned from atomic_create(), though not if vfs_create() returns an error (in the case where ->atomic_create is not supported). The caller - nfsd4_create_file() - is made aware of this by checking path->dentry, which will either be a counted reference to a dentry, or an error pointer. However the change to use start_creating()/end_creating() (which landed shortly before the dentry_create() change landed, though was likely developed around the same time) means that nfsd4_create_file() *needs* a valid dentry so that it can unlock the parent. The net result is that if NFSD exports a filesystem which uses ->atomic_create, and if a call to ->atomic_create returns an error, then nfsd4_create_file() will pass an error pointer to end_creating() and the parent will not be unlocked. Fix this by changing dentry_create() to make sure path->dentry is always a valid dentry, never an error-pointer. The actual error is already returned a different way. Note that if ->atomic_create() returns a different dentry (which may not be possible in practice) we are guaranteed (because it is only ever provided by d_spliace_alias()) that it will have the same d_parent and so it will have the same effect when passed to end_creating().

In the Linux kernel, the following vulnerability has been resolved: libceph: make free_choose_arg_map() resilient to partial allocation free_choose_arg_map() may dereference a NULL pointer if its caller fails after a partial allocation. For example, in decode_choose_args(), if allocation of arg_map->args fails, execution jumps to the fail label and free_choose_arg_map() is called. Since arg_map->size is updated to a non-zero value before memory allocation, free_choose_arg_map() will iterate over arg_map->args and dereference a NULL pointer. To prevent this potential NULL pointer dereference and make free_choose_arg_map() more resilient, add checks for pointers before iterating.

In the Linux kernel, the following vulnerability has been resolved: gue: Fix skb memleak with inner IP protocol 0. syzbot reported skb memleak below. [0] The repro generated a GUE packet with its inner protocol 0. gue_udp_recv() returns -guehdr->proto_ctype for "resubmit" in ip_protocol_deliver_rcu(), but this only works with non-zero protocol number. Let's drop such packets. Note that 0 is a valid number (IPv6 Hop-by-Hop Option). I think it is not practical to encap HOPOPT in GUE, so once someone starts to complain, we could pass down a resubmit flag pointer to distinguish two zeros from the upper layer: * no error * resubmit HOPOPT [0] BUG: memory leak unreferenced object 0xffff888109695a00 (size 240): comm "syz.0.17", pid 6088, jiffies 4294943096 hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 40 c2 10 81 88 ff ff 00 00 00 00 00 00 00 00 .@.............. backtrace (crc a84b336f): kmemleak_alloc_recursive include/linux/kmemleak.h:44 [inline] slab_post_alloc_hook mm/slub.c:4958 [inline] slab_alloc_node mm/slub.c:5263 [inline] kmem_cache_alloc_noprof+0x3b4/0x590 mm/slub.c:5270 __build_skb+0x23/0x60 net/core/skbuff.c:474 build_skb+0x20/0x190 net/core/skbuff.c:490 __tun_build_skb drivers/net/tun.c:1541 [inline] tun_build_skb+0x4a1/0xa40 drivers/net/tun.c:1636 tun_get_user+0xc12/0x2030 drivers/net/tun.c:1770 tun_chr_write_iter+0x71/0x120 drivers/net/tun.c:1999 new_sync_write fs/read_write.c:593 [inline] vfs_write+0x45d/0x710 fs/read_write.c:686 ksys_write+0xa7/0x170 fs/read_write.c:738 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xa4/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: tls: Purge async_hold in tls_decrypt_async_wait() The async_hold queue pins encrypted input skbs while the AEAD engine references their scatterlist data. Once tls_decrypt_async_wait() returns, every AEAD operation has completed and the engine no longer references those skbs, so they can be freed unconditionally. A subsequent patch adds batch async decryption to tls_sw_read_sock(), introducing a new call site that must drain pending AEAD operations and release held skbs. Move __skb_queue_purge(&ctx->async_hold) into tls_decrypt_async_wait() so the purge is centralized and every caller -- recvmsg's drain path, the -EBUSY fallback in tls_do_decryption(), and the new read_sock batch path -- releases held skbs on synchronization without each site managing the purge independently. This fixes a leak when tls_strp_msg_hold() fails part-way through, after having added some cloned skbs to the async_hold queue. tls_decrypt_sg() will then call tls_decrypt_async_wait() to process all pending decrypts, and drop back to synchronous mode, but tls_sw_recvmsg() only flushes the async_hold queue when one record has been processed in "fully-async" mode, which may not be the case here. [pabeni@redhat.com: added leak comment]

In the Linux kernel, the following vulnerability has been resolved: net/smc: avoid early lgr access in smc_clc_wait_msg A CLC decline can be received while the handshake is still in an early stage, before the connection has been associated with a link group. The decline handling in smc_clc_wait_msg() updates link-group level sync state for first-contact declines, but that state only exists after link group setup has completed. Guard the link-group update accordingly and keep the per-socket peer diagnosis handling unchanged. This preserves the existing sync_err handling for established link-group contexts and avoids touching link-group state before it is available.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_conncount: increase the connection clean up limit to 64 After the optimization to only perform one GC per jiffy, a new problem was introduced. If more than 8 new connections are tracked per jiffy the list won't be cleaned up fast enough possibly reaching the limit wrongly. In order to prevent this issue, only skip the GC if it was already triggered during the same jiffy and the increment is lower than the clean up limit. In addition, increase the clean up limit to 64 connections to avoid triggering GC too often and do more effective GCs. This has been tested using a HTTP server and several performance tools while having nft_connlimit/xt_connlimit or OVS limit configured. Output of slowhttptest + OVS limit at 52000 connections: slow HTTP test status on 340th second: initializing: 0 pending: 432 connected: 51998 error: 0 closed: 0 service available: YES

In the Linux kernel, the following vulnerability has been resolved: cppc_cpufreq: Fix possible null pointer dereference cppc_cpufreq_get_rate() and hisi_cppc_cpufreq_get_rate() can be called from different places with various parameters. So cpufreq_cpu_get() can return null as 'policy' in some circumstances. Fix this bug by adding null return check. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix WQ_MEM_RECLAIM warning When sunrpc is used, if a reset triggered, our wq may lead the following trace: workqueue: WQ_MEM_RECLAIM xprtiod:xprt_rdma_connect_worker [rpcrdma] is flushing !WQ_MEM_RECLAIM hns_roce_irq_workq:flush_work_handle [hns_roce_hw_v2] WARNING: CPU: 0 PID: 8250 at kernel/workqueue.c:2644 check_flush_dependency+0xe0/0x144 Call trace: check_flush_dependency+0xe0/0x144 start_flush_work.constprop.0+0x1d0/0x2f0 __flush_work.isra.0+0x40/0xb0 flush_work+0x14/0x30 hns_roce_v2_destroy_qp+0xac/0x1e0 [hns_roce_hw_v2] ib_destroy_qp_user+0x9c/0x2b4 rdma_destroy_qp+0x34/0xb0 rpcrdma_ep_destroy+0x28/0xcc [rpcrdma] rpcrdma_ep_put+0x74/0xb4 [rpcrdma] rpcrdma_xprt_disconnect+0x1d8/0x260 [rpcrdma] xprt_rdma_connect_worker+0xc0/0x120 [rpcrdma] process_one_work+0x1cc/0x4d0 worker_thread+0x154/0x414 kthread+0x104/0x144 ret_from_fork+0x10/0x18 Since QP destruction frees memory, this wq should have the WQ_MEM_RECLAIM.

In the Linux kernel, the following vulnerability has been resolved: ipmi: Add limits to event and receive message requests The driver would just fetch events and receive messages until the BMC said it was done. To avoid issues with BMCs that never say they are done, add a limit of 10 fetches at a time. In addition, an si interface has an attn state it can return from the hardware which is supposed to cause a flag fetch to see if the driver needs to fetch events or message or a few other things. If the attn bit gets stuck, it's a similar problem. So allow messages in between flag fetches so the driver itself doesn't get stuck. This is a more general fix than the previous fix for the specific bad BMC, but should fix the more general issue of a BMC that won't stop saying it has data. This has been there from the beginning of the driver. It's not a bug per-se, but it is accounting for bugs in BMCs.

In the Linux kernel, the following vulnerability has been resolved: net: ks8851: Reinstate disabling of BHs around IRQ handler If the driver executes ks8851_irq() AND a TX packet has been sent, then the driver enables TX queue via netif_wake_queue() which schedules TX softirq to queue packets for this device. If CONFIG_PREEMPT_RT=y is set AND a packet has also been received by the MAC, then ks8851_rx_pkts() calls netdev_alloc_skb_ip_align() to allocate SKBs for the received packets. If netdev_alloc_skb_ip_align() is called with BH enabled, then local_bh_enable() at the end of netdev_alloc_skb_ip_align() will trigger the pending softirq processing, which may ultimately call the .xmit callback ks8851_start_xmit_par(). The ks8851_start_xmit_par() will try to lock struct ks8851_net_par .lock spinlock, which is already locked by ks8851_irq() from which ks8851_start_xmit_par() was called. This leads to a deadlock, which is reported by the kernel, including a trace listed below. If CONFIG_PREEMPT_RT is not set, then since commit 0913ec336a6c0 ("net: ks8851: Fix deadlock with the SPI chip variant") the deadlock can also be triggered without received packet in the RX FIFO. The pending softirqs will be processed on return from spin_unlock_bh(&ks->statelock) in ks8851_irq(), which triggers the deadlock as well. Fix the problem by disabling BH around critical sections, including the IRQ handler, thus preventing the net_tx_action() softirq from triggering during these critical sections. The net_tx_action() softirq is triggered once BH are re-enabled and at the end of the IRQ handler, once all the other IRQ handler actions have been completed. __schedule from schedule_rtlock+0x1c/0x34 schedule_rtlock from rtlock_slowlock_locked+0x548/0x904 rtlock_slowlock_locked from rt_spin_lock+0x60/0x9c rt_spin_lock from ks8851_start_xmit_par+0x74/0x1a8 ks8851_start_xmit_par from netdev_start_xmit+0x20/0x44 netdev_start_xmit from dev_hard_start_xmit+0xd0/0x188 dev_hard_start_xmit from sch_direct_xmit+0xb8/0x25c sch_direct_xmit from __qdisc_run+0x1f8/0x4ec __qdisc_run from qdisc_run+0x1c/0x28 qdisc_run from net_tx_action+0x1f0/0x268 net_tx_action from handle_softirqs+0x1a4/0x270 handle_softirqs from __local_bh_enable_ip+0xcc/0xe0 __local_bh_enable_ip from __alloc_skb+0xd8/0x128 __alloc_skb from __netdev_alloc_skb+0x3c/0x19c __netdev_alloc_skb from ks8851_irq+0x388/0x4d4 ks8851_irq from irq_thread_fn+0x24/0x64 irq_thread_fn from irq_thread+0x178/0x28c irq_thread from kthread+0x12c/0x138 kthread from ret_from_fork+0x14/0x28

In the Linux kernel, the following vulnerability has been resolved: RDMA/rxe: Reject unknown opcodes before ICRC processing Even after applying commit 7244491dab34 ("RDMA/rxe: Validate pad and ICRC before payload_size() in rxe_rcv"), a single unauthenticated UDP packet can still trigger panic. That patch handled payload_size() underflow only for valid opcodes with short packets, not for packets carrying an unknown opcode. The unknown-opcode OOB read described below predates that commit and reaches back to the initial Soft RoCE driver. The check added there reads pkt->paylen < header_size(pkt) + bth_pad(pkt) + RXE_ICRC_SIZE where header_size(pkt) expands to rxe_opcode[pkt->opcode].length. The rxe_opcode[] array has 256 entries but is only populated for defined IB opcodes; any other entry (for example opcode 0xff) is zero-initialized, so length == 0 and the check degenerates to pkt->paylen < 0 + bth_pad(pkt) + RXE_ICRC_SIZE which does not constrain pkt->paylen enough. rxe_icrc_hdr() then computes rxe_opcode[pkt->opcode].length - RXE_BTH_BYTES which underflows when length == 0 and passes a huge value to rxe_crc32(), causing an out-of-bounds read of the skb payload. Reproduced on v7.0-rc7 with that fix applied, QEMU/KVM with CONFIG_RDMA_RXE=y and CONFIG_KASAN=y, after rdma link add rxe0 type rxe netdev eth0 A single 48-byte UDP packet to port 4791 with BTH opcode=0xff and QPN=IB_MULTICAST_QPN triggers: BUG: KASAN: slab-out-of-bounds in crc32_le+0x115/0x170 Read of size 1 at addr ... The buggy address is located 0 bytes to the right of allocated 704-byte region Call Trace: crc32_le+0x115/0x170 rxe_icrc_hdr.isra.0+0x226/0x300 rxe_icrc_check+0x13f/0x3a0 rxe_rcv+0x6e1/0x16e0 rxe_udp_encap_recv+0x20a/0x320 udp_queue_rcv_one_skb+0x7ed/0x12c0 Subsequent packets with the same shape fault on unmapped memory and panic the kernel. The trigger requires only module load and "rdma link add"; no QP, no connection, and no authentication. Fix this by rejecting packets whose opcode has no rxe_opcode[] entry, detected via the zero mask or zero length, before any length arithmetic runs.

In the Linux kernel, the following vulnerability has been resolved: flow_dissector: do not dissect PPPoE PFC frames RFC 2516 Section 7 states that Protocol Field Compression (PFC) is NOT RECOMMENDED for PPPoE. In practice, pppd does not support negotiating PFC for PPPoE sessions, and the flow dissector driver has assumed an uncompressed frame until the blamed commit. During the review process of that commit [1], support for PFC is suggested. However, having a compressed (1-byte) protocol field means the subsequent PPP payload is shifted by one byte, causing 4-byte misalignment for the network header and an unaligned access exception on some architectures. The exception can be reproduced by sending a PPPoE PFC frame to an ethernet interface of a MIPS board, with RPS enabled, even if no PPPoE session is active on that interface: $ 0 : 00000000 80c40000 00000000 85144817 $ 4 : 00000008 00000100 80a75758 81dc9bb8 $ 8 : 00000010 8087ae2c 0000003d 00000000 $12 : 000000e0 00000039 00000000 00000000 $16 : 85043240 80a75758 81dc9bb8 00006488 $20 : 0000002f 00000007 85144810 80a70000 $24 : 81d1bda0 00000000 $28 : 81dc8000 81dc9aa8 00000000 805ead08 Hi : 00009d51 Lo : 2163358a epc : 805e91f0 __skb_flow_dissect+0x1b0/0x1b50 ra : 805ead08 __skb_get_hash_net+0x74/0x12c Status: 11000403 KERNEL EXL IE Cause : 40800010 (ExcCode 04) BadVA : 85144817 PrId : 0001992f (MIPS 1004Kc) Call Trace: [<805e91f0>] __skb_flow_dissect+0x1b0/0x1b50 [<805ead08>] __skb_get_hash_net+0x74/0x12c [<805ef330>] get_rps_cpu+0x1b8/0x3fc [<805fca70>] netif_receive_skb_list_internal+0x324/0x364 [<805fd120>] napi_complete_done+0x68/0x2a4 [<8058de5c>] mtk_napi_rx+0x228/0xfec [<805fd398>] __napi_poll+0x3c/0x1c4 [<805fd754>] napi_threaded_poll_loop+0x234/0x29c [<805fd848>] napi_threaded_poll+0x8c/0xb0 [<80053544>] kthread+0x104/0x12c [<80002bd8>] ret_from_kernel_thread+0x14/0x1c Code: 02d51821 1060045b 00000000 <8c640000> 3084000f 2c820005 144001a2 00042080 8e220000 To reduce the attack surface and maintain performance, do not process PPPoE PFC frames. [1] https://lore.kernel.org/r/20220630231016.GA392@debian.home

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix rxkad crypto unalignment handling Fix handling of a packet with a misaligned crypto length. Also handle non-ENOMEM errors from decryption by aborting. Further, remove the WARN_ON_ONCE() so that it can't be remotely triggered (a trace line can still be emitted).

In the Linux kernel, the following vulnerability has been resolved: net: strparser: fix skb_head leak in strp_abort_strp() When the stream parser is aborted, for example after a message assembly timeout, it can still hold a reference to a partially assembled message in strp->skb_head. That skb is not released in strp_abort_strp(), which leaks the partially assembled message and can be triggered repeatedly to exhaust memory. Fix this by freeing strp->skb_head and resetting the parser state in the abort path. Leave strp_stop() unchanged so final cleanup still happens in strp_done() after the work and timer have been synchronized.

In the Linux kernel, the following vulnerability has been resolved: libceph: Prevent potential null-ptr-deref in ceph_handle_auth_reply() If a message of type CEPH_MSG_AUTH_REPLY contains a zero value for both protocol and result, this is currently not treated as an error. In case of ac->negotiating == true and ac->protocol > 0, this leads to setting ac->protocol = 0 and ac->ops = NULL. Thereafter, the check for ac->protocol != protocol returns false, and init_protocol() is not called. Subsequently, ac->ops->handle_reply() is called, which leads to a null pointer dereference, because ac->ops is still NULL. This patch changes the check for ac->protocol != protocol to !ac->protocol, as this also includes the case when the protocol was set to zero in the message. This causes the message to be treated as containing a bad auth protocol.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix "scheduling while atomic" in IPsec MAC address query Fix a "scheduling while atomic" bug in mlx5e_ipsec_init_macs() by replacing mlx5_query_mac_address() with ether_addr_copy() to get the local MAC address directly from netdev->dev_addr. The issue occurs because mlx5_query_mac_address() queries the hardware which involves mlx5_cmd_exec() that can sleep, but it is called from the mlx5e_ipsec_handle_event workqueue which runs in atomic context. The MAC address is already available in netdev->dev_addr, so no need to query hardware. This avoids the sleeping call and resolves the bug. Call trace: BUG: scheduling while atomic: kworker/u112:2/69344/0x00000200 __schedule+0x7ab/0xa20 schedule+0x1c/0xb0 schedule_timeout+0x6e/0xf0 __wait_for_common+0x91/0x1b0 cmd_exec+0xa85/0xff0 [mlx5_core] mlx5_cmd_exec+0x1f/0x50 [mlx5_core] mlx5_query_nic_vport_mac_address+0x7b/0xd0 [mlx5_core] mlx5_query_mac_address+0x19/0x30 [mlx5_core] mlx5e_ipsec_init_macs+0xc1/0x720 [mlx5_core] mlx5e_ipsec_build_accel_xfrm_attrs+0x422/0x670 [mlx5_core] mlx5e_ipsec_handle_event+0x2b9/0x460 [mlx5_core] process_one_work+0x178/0x2e0 worker_thread+0x2ea/0x430

In the Linux kernel, the following vulnerability has been resolved: ovpn: tcp - fix packet extraction from stream When processing TCP stream data in ovpn_tcp_recv, we receive large cloned skbs from __strp_rcv that may contain multiple coalesced packets. The current implementation has two bugs: 1. Header offset overflow: Using pskb_pull with large offsets on coalesced skbs causes skb->data - skb->head to exceed the u16 storage of skb->network_header. This causes skb_reset_network_header to fail on the inner decapsulated packet, resulting in packet drops. 2. Unaligned protocol headers: Extracting packets from arbitrary positions within the coalesced TCP stream provides no alignment guarantees for the packet data causing performance penalties on architectures without efficient unaligned access. Additionally, openvpn's 2-byte length prefix on TCP packets causes the subsequent 4-byte opcode and packet ID fields to be inherently misaligned. Fix both issues by allocating a new skb for each openvpn packet and using skb_copy_bits to extract only the packet content into the new buffer, skipping the 2-byte length prefix. Also, check the length before invoking the function that performs the allocation to avoid creating an invalid skb. If the packet has to be forwarded to userspace the 2-byte prefix can be pushed to the head safely, without misalignment. As a side effect, this approach also avoids the expensive linearization that pskb_pull triggers on cloned skbs with page fragments. In testing, this resulted in TCP throughput improvements of up to 74%.

In the Linux kernel, the following vulnerability has been resolved: net: correctly handle tunneled traffic on IPV6_CSUM GSO fallback NETIF_F_IPV6_CSUM only advertises support for checksum offload of packets without IPv6 extension headers. Packets with extension headers must fall back onto software checksumming. Since TSO depends on checksum offload, those must revert to GSO. The below commit introduces that fallback. It always checks network header length. For tunneled packets, the inner header length must be checked instead. Extend the check accordingly. A special case is tunneled packets without inner IP protocol. Such as RFC 6951 SCTP in UDP. Those are not standard IPv6 followed by transport header either, so also must revert to the software GSO path.

In the Linux kernel, the following vulnerability has been resolved: net/rds: Clear reconnect pending bit When canceling the reconnect worker, care must be taken to reset the reconnect-pending bit. If the reconnect worker has not yet been scheduled before it is canceled, the reconnect-pending bit will stay on forever.

In the Linux kernel, the following vulnerability has been resolved: ipv4: icmp: fix null-ptr-deref in icmp_build_probe() ipv6_stub->ipv6_dev_find() may return ERR_PTR(-EAFNOSUPPORT) when the IPv6 stack is not active (CONFIG_IPV6=m and not loaded), and passing this error pointer to dev_hold() will cause a kernel crash with null-ptr-deref. Instead, silently discard the request. RFC 8335 does not appear to define a specific response for the case where an IPv6 interface identifier is syntactically valid but the implementation cannot perform the lookup at runtime, and silently dropping the request may safer than misreporting "No Such Interface".

In the Linux kernel, the following vulnerability has been resolved: scsi: target: file: Use kzalloc_flex for aio_cmd The target_core_file doesn't initialize the aio_cmd->iocb for the ki_write_stream. When a write command fd_execute_rw_aio() is executed, we may get a bogus ki_write_stream value, causing unintended write failure status when checking iocb->ki_write_stream > max_write_streams in the block device. Let's just use kzalloc_flex when allocating the aio_cmd and let ki_write_stream=0 to fix this issue.

In the Linux kernel, the following vulnerability has been resolved: arm64: dts: qcom: monaco: Reserve full Gunyah metadata region We observe spurious "Synchronous External Abort" exceptions (ESR=0x96000010) and kernel crashes on Monaco-based platforms. These faults are caused by the kernel inadvertently accessing hypervisor-owned memory that is not properly marked as reserved. >From boot log, The Qualcomm hypervisor reports the memory range at 0x91a80000 of size 0x80000 (512 KiB) as hypervisor-owned: qhee_hyp_assign_remove_memory: 0x91a80000/0x80000 -> ret 0 However, the EFI memory map provided by firmware only reserves the subrange 0x91a40000–0x91a87fff (288 KiB). The remaining portion (0x91a88000–0x91afffff) is incorrectly reported as conventional memory (from efi debug): efi: 0x000091a40000-0x000091a87fff [Reserved...] efi: 0x000091a88000-0x0000938fffff [Conventional...] As a result, the allocator may hand out PFNs inside the hypervisor owned region, causing fatal aborts when the kernel accesses those addresses. Add a reserved-memory carveout for the Gunyah hypervisor metadata at 0x91a80000 (512 KiB) and mark it as no-map so Linux does not map or allocate from this area. For the record: Hyp version: gunyah-e78adb36e debug (2025-11-17 05:38:05 UTC) UEFI Ver: 6.0.260122.BOOT.MXF.1.0.c1-00449-KODIAKLA-1

In the Linux kernel, the following vulnerability has been resolved: ntfs: ->d_compare() must not block ... so don't use __getname() there. Switch it (and ntfs_d_hash(), while we are at it) to kmalloc(PATH_MAX, GFP_NOWAIT). Yes, ntfs_d_hash() almost certainly can do with smaller allocations, but let ntfs folks deal with that - keep the allocation size as-is for now. Stop abusing names_cachep in ntfs, period - various uses of that thing in there have nothing to do with pathnames; just use k[mz]alloc() and be done with that. For now let's keep sizes as-in, but AFAICS none of the users actually want PATH_MAX.

In the Linux kernel, the following vulnerability has been resolved: libceph: Use u32 for non-negative values in ceph_monmap_decode() This patch fixes unnecessary implicit conversions that change signedness of blob_len and num_mon in ceph_monmap_decode(). Currently blob_len and num_mon are (signed) int variables. They are used to hold values that are always non-negative and get assigned in ceph_decode_32_safe(), which is meant to assign u32 values. Both variables are subsequently used as unsigned values, and the value of num_mon is further assigned to monmap->num_mon, which is of type u32. Therefore, both variables should be of type u32. This is especially relevant for num_mon. If the value read from the incoming message is very large, it is interpreted as a negative value, and the check for num_mon > CEPH_MAX_MON does not catch it. This leads to the attempt to allocate a very large chunk of memory for monmap, which will most likely fail. In this case, an unnecessary attempt to allocate memory is performed, and -ENOMEM is returned instead of -EINVAL.

In the Linux kernel, the following vulnerability has been resolved: net: ncsi: fix skb leak in error paths Early return paths in NCSI RX and AEN handlers fail to release the received skb, resulting in a memory leak. Specifically, ncsi_aen_handler() returns on invalid AEN packets without consuming the skb. Similarly, ncsi_rcv_rsp() exits early when failing to resolve the NCSI device, response handler, or request, leaving the skb unfreed.

In the Linux kernel, the following vulnerability has been resolved: octeontx2-af: Workaround SQM/PSE stalls by disabling sticky NIX SQ manager sticky mode is known to cause stalls when multiple SQs share an SMQ and transmit concurrently. Additionally, PSE may deadlock on transitions between sticky and non-sticky transmissions. There is also a credit drop issue observed when certain condition clocks are gated. work around these hardware errata by: - Disabling SQM sticky operation: - Clear TM6 (bit 15) - Clear TM11 (bit 14) - Disabling sticky → non-sticky transition path that can deadlock PSE: - Clear TM5 (bit 23) - Preventing credit drops by keeping the control-flow clock enabled: - Set TM9 (bit 21) These changes are applied via NIX_AF_SQM_DBG_CTL_STATUS. With this configuration the SQM/PSE maintain forward progress under load without credit loss, at the cost of disabling sticky optimizations.

In the Linux kernel, the following vulnerability has been resolved: net: bonding: Fix nd_tbl NULL dereference when IPv6 is disabled When booting with the 'ipv6.disable=1' parameter, the nd_tbl is never initialized because inet6_init() exits before ndisc_init() is called which initializes it. If bonding ARP/NS validation is enabled, an IPv6 NS/NA packet received on a slave can reach bond_validate_na(), which calls bond_has_this_ip6(). That path calls ipv6_chk_addr() and can crash in __ipv6_chk_addr_and_flags(). BUG: kernel NULL pointer dereference, address: 00000000000005d8 Oops: Oops: 0000 [#1] SMP NOPTI RIP: 0010:__ipv6_chk_addr_and_flags+0x69/0x170 Call Trace: <IRQ> ipv6_chk_addr+0x1f/0x30 bond_validate_na+0x12e/0x1d0 [bonding] ? __pfx_bond_handle_frame+0x10/0x10 [bonding] bond_rcv_validate+0x1a0/0x450 [bonding] bond_handle_frame+0x5e/0x290 [bonding] ? srso_alias_return_thunk+0x5/0xfbef5 __netif_receive_skb_core.constprop.0+0x3e8/0xe50 ? srso_alias_return_thunk+0x5/0xfbef5 ? update_cfs_rq_load_avg+0x1a/0x240 ? srso_alias_return_thunk+0x5/0xfbef5 ? __enqueue_entity+0x5e/0x240 __netif_receive_skb_one_core+0x39/0xa0 process_backlog+0x9c/0x150 __napi_poll+0x30/0x200 ? srso_alias_return_thunk+0x5/0xfbef5 net_rx_action+0x338/0x3b0 handle_softirqs+0xc9/0x2a0 do_softirq+0x42/0x60 </IRQ> <TASK> __local_bh_enable_ip+0x62/0x70 __dev_queue_xmit+0x2d3/0x1000 ? srso_alias_return_thunk+0x5/0xfbef5 ? srso_alias_return_thunk+0x5/0xfbef5 ? packet_parse_headers+0x10a/0x1a0 packet_sendmsg+0x10da/0x1700 ? kick_pool+0x5f/0x140 ? srso_alias_return_thunk+0x5/0xfbef5 ? __queue_work+0x12d/0x4f0 __sys_sendto+0x1f3/0x220 __x64_sys_sendto+0x24/0x30 do_syscall_64+0x101/0xf80 ? exc_page_fault+0x6e/0x170 ? srso_alias_return_thunk+0x5/0xfbef5 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> Fix this by checking ipv6_mod_enabled() before dispatching IPv6 packets to bond_na_rcv(). If IPv6 is disabled, return early from bond_rcv_validate() and avoid the path to ipv6_chk_addr().

In the Linux kernel, the following vulnerability has been resolved: net: bridge: vlan: fix memory leak in __allowed_ingress When using per-vlan state, if vlan snooping and stats are disabled, untagged or priority-tagged ingress frame will go to check pvid state. If the port state is forwarding and the pvid state is not learning/forwarding, untagged or priority-tagged frame will be dropped but skb memory is not freed. Should free skb when __allowed_ingress returns false.

A vulnerability classified as problematic was found in Linux Kernel. This vulnerability affects the function macvlan_handle_frame of the file drivers/net/macvlan.c of the component skb. The manipulation leads to memory leak. The attack can be initiated remotely. It is recommended to apply a patch to fix this issue. The identifier of this vulnerability is VDB-211024.

In the Linux kernel, the following vulnerability has been resolved: nvmet: avoid recursive nvmet-wq flush in nvmet_ctrl_free nvmet_tcp_release_queue_work() runs on nvmet-wq and can drop the final controller reference through nvmet_cq_put(). If that triggers nvmet_ctrl_free(), the teardown path flushes ctrl->async_event_work on the same nvmet-wq. Call chain: nvmet_tcp_schedule_release_queue() kref_put(&queue->kref, nvmet_tcp_release_queue) nvmet_tcp_release_queue() queue_work(nvmet_wq, &queue->release_work) <--- nvmet_wq process_one_work() nvmet_tcp_release_queue_work() nvmet_cq_put(&queue->nvme_cq) nvmet_cq_destroy() nvmet_ctrl_put(cq->ctrl) nvmet_ctrl_free() flush_work(&ctrl->async_event_work) <--- nvmet_wq Previously Scheduled by :- nvmet_add_async_event queue_work(nvmet_wq, &ctrl->async_event_work); This trips lockdep with a possible recursive locking warning. [ 5223.015876] run blktests nvme/003 at 2026-04-07 20:53:55 [ 5223.061801] loop0: detected capacity change from 0 to 2097152 [ 5223.072206] nvmet: adding nsid 1 to subsystem blktests-subsystem-1 [ 5223.088368] nvmet_tcp: enabling port 0 (127.0.0.1:4420) [ 5223.126086] nvmet: Created discovery controller 1 for subsystem nqn.2014-08.org.nvmexpress.discovery for NQN nqn.2014-08.org.nvmexpress:uuid:0f01fb42-9f7f-4856-b0b3-51e60b8de349. [ 5223.128453] nvme nvme1: new ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery", addr 127.0.0.1:4420, hostnqn: nqn.2014-08.org.nvmexpress:uuid:0f01fb42-9f7f-4856-b0b3-51e60b8de349 [ 5233.199447] nvme nvme1: Removing ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery" [ 5233.227718] ============================================ [ 5233.231283] WARNING: possible recursive locking detected [ 5233.234696] 7.0.0-rc3nvme+ #20 Tainted: G O N [ 5233.238434] -------------------------------------------- [ 5233.241852] kworker/u192:6/2413 is trying to acquire lock: [ 5233.245429] ffff888111632548 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: touch_wq_lockdep_map+0x26/0x90 [ 5233.251438] but task is already holding lock: [ 5233.255254] ffff888111632548 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x5cc/0x6e0 [ 5233.261125] other info that might help us debug this: [ 5233.265333] Possible unsafe locking scenario: [ 5233.269217] CPU0 [ 5233.270795] ---- [ 5233.272436] lock((wq_completion)nvmet-wq); [ 5233.275241] lock((wq_completion)nvmet-wq); [ 5233.278020] *** DEADLOCK *** [ 5233.281793] May be due to missing lock nesting notation [ 5233.286195] 3 locks held by kworker/u192:6/2413: [ 5233.289192] #0: ffff888111632548 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x5cc/0x6e0 [ 5233.294569] #1: ffffc9000e2a7e40 ((work_completion)(&queue->release_work)){+.+.}-{0:0}, at: process_one_work+0x1c5/0x6e0 [ 5233.300128] #2: ffffffff82d7dc40 (rcu_read_lock){....}-{1:3}, at: __flush_work+0x62/0x530 [ 5233.304290] stack backtrace: [ 5233.306520] CPU: 4 UID: 0 PID: 2413 Comm: kworker/u192:6 Tainted: G O N 7.0.0-rc3nvme+ #20 PREEMPT(full) [ 5233.306524] Tainted: [O]=OOT_MODULE, [N]=TEST [ 5233.306525] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014 [ 5233.306527] Workqueue: nvmet-wq nvmet_tcp_release_queue_work [nvmet_tcp] [ 5233.306532] Call Trace: [ 5233.306534] <TASK> [ 5233.306536] dump_stack_lvl+0x73/0xb0 [ 5233.306552] print_deadlock_bug+0x225/0x2f0 [ 5233.306556] __lock_acquire+0x13f0/0x2290 [ 5233.306563] lock_acquire+0xd0/0x300 [ 5233.306565] ? touch_wq_lockdep_map+0x26/0x90 [ 5233.306571] ? __flush_work+0x20b/0x530 [ 5233.306573] ? touch_wq_lockdep_map+0x26/0x90 [ 5233.306577] touch_wq_lockdep_map+0x3b/0x90 [ 5233.306580] ? touch_wq_lockdep_map+0x26/0x90 [ 52 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: mm/vmalloc: do not trigger BUG() on BH disabled context __get_vm_area_node() currently triggers a BUG() if in_interrupt() returns true. However, in_interrupt() also reports true when BH are disabled. The bridge code can call rhashtable_lookup_insert_fast() with bottom halves disabled: __vlan_add() -> br_fdb_add_local() spin_lock_bh(&br->hash_lock); <-- Disable BH -> fdb_add_local() -> fdb_create() -> rhashtable_lookup_insert_fast() -> kvmalloc() -> vmalloc() -> __get_vm_area_node() -> BUG_ON(in_interrupt()) spin_unlock_bh(&br->hash_lock) this triggers the BUG() despite the caller not being in NMI or hard IRQ context. Replace the in_interrupt() check with in_nmi() || in_hardirq().

In the Linux kernel, the following vulnerability has been resolved: sunrpc: fix handling of server side tls alerts Scott Mayhew discovered a security exploit in NFS over TLS in tls_alert_recv() due to its assumption it can read data from the msg iterator's kvec.. kTLS implementation splits TLS non-data record payload between the control message buffer (which includes the type such as TLS aler or TLS cipher change) and the rest of the payload (say TLS alert's level/description) which goes into the msg payload buffer. This patch proposes to rework how control messages are setup and used by sock_recvmsg(). If no control message structure is setup, kTLS layer will read and process TLS data record types. As soon as it encounters a TLS control message, it would return an error. At that point, NFS can setup a kvec backed msg buffer and read in the control message such as a TLS alert. Msg iterator can advance the kvec pointer as a part of the copy process thus we need to revert the iterator before calling into the tls_alert_recv.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: limit repeated connections from clients with the same IP Repeated connections from clients with the same IP address may exhaust the max connections and prevent other normal client connections. This patch limit repeated connections from clients with the same IP.

In the Linux kernel, the following vulnerability has been resolved: arm64: mm: Handle invalid large leaf mappings correctly It has been possible for a long time to mark ptes in the linear map as invalid. This is done for secretmem, kfence, realm dma memory un/share, and others, by simply clearing the PTE_VALID bit. But until commit a166563e7ec37 ("arm64: mm: support large block mapping when rodata=full") large leaf mappings were never made invalid in this way. It turns out various parts of the code base are not equipped to handle invalid large leaf mappings (in the way they are currently encoded) and I've observed a kernel panic while booting a realm guest on a BBML2_NOABORT system as a result: [ 15.432706] software IO TLB: Memory encryption is active and system is using DMA bounce buffers [ 15.476896] Unable to handle kernel paging request at virtual address ffff000019600000 [ 15.513762] Mem abort info: [ 15.527245] ESR = 0x0000000096000046 [ 15.548553] EC = 0x25: DABT (current EL), IL = 32 bits [ 15.572146] SET = 0, FnV = 0 [ 15.592141] EA = 0, S1PTW = 0 [ 15.612694] FSC = 0x06: level 2 translation fault [ 15.640644] Data abort info: [ 15.661983] ISV = 0, ISS = 0x00000046, ISS2 = 0x00000000 [ 15.694875] CM = 0, WnR = 1, TnD = 0, TagAccess = 0 [ 15.723740] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 15.755776] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000081f3f000 [ 15.800410] [ffff000019600000] pgd=0000000000000000, p4d=180000009ffff403, pud=180000009fffe403, pmd=00e8000199600704 [ 15.855046] Internal error: Oops: 0000000096000046 [#1] SMP [ 15.886394] Modules linked in: [ 15.900029] CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 7.0.0-rc4-dirty #4 PREEMPT [ 15.935258] Hardware name: linux,dummy-virt (DT) [ 15.955612] pstate: 21400005 (nzCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--) [ 15.986009] pc : __pi_memcpy_generic+0x128/0x22c [ 16.006163] lr : swiotlb_bounce+0xf4/0x158 [ 16.024145] sp : ffff80008000b8f0 [ 16.038896] x29: ffff80008000b8f0 x28: 0000000000000000 x27: 0000000000000000 [ 16.069953] x26: ffffb3976d261ba8 x25: 0000000000000000 x24: ffff000019600000 [ 16.100876] x23: 0000000000000001 x22: ffff0000043430d0 x21: 0000000000007ff0 [ 16.131946] x20: 0000000084570010 x19: 0000000000000000 x18: ffff00001ffe3fcc [ 16.163073] x17: 0000000000000000 x16: 00000000003fffff x15: 646e612065766974 [ 16.194131] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 [ 16.225059] x11: 0000000000000000 x10: 0000000000000010 x9 : 0000000000000018 [ 16.256113] x8 : 0000000000000018 x7 : 0000000000000000 x6 : 0000000000000000 [ 16.287203] x5 : ffff000019607ff0 x4 : ffff000004578000 x3 : ffff000019600000 [ 16.318145] x2 : 0000000000007ff0 x1 : ffff000004570010 x0 : ffff000019600000 [ 16.349071] Call trace: [ 16.360143] __pi_memcpy_generic+0x128/0x22c (P) [ 16.380310] swiotlb_tbl_map_single+0x154/0x2b4 [ 16.400282] swiotlb_map+0x5c/0x228 [ 16.415984] dma_map_phys+0x244/0x2b8 [ 16.432199] dma_map_page_attrs+0x44/0x58 [ 16.449782] virtqueue_map_page_attrs+0x38/0x44 [ 16.469596] virtqueue_map_single_attrs+0xc0/0x130 [ 16.490509] virtnet_rq_alloc.isra.0+0xa4/0x1fc [ 16.510355] try_fill_recv+0x2a4/0x584 [ 16.526989] virtnet_open+0xd4/0x238 [ 16.542775] __dev_open+0x110/0x24c [ 16.558280] __dev_change_flags+0x194/0x20c [ 16.576879] netif_change_flags+0x24/0x6c [ 16.594489] dev_change_flags+0x48/0x7c [ 16.611462] ip_auto_config+0x258/0x1114 [ 16.628727] do_one_initcall+0x80/0x1c8 [ 16.645590] kernel_init_freeable+0x208/0x2f0 [ 16.664917] kernel_init+0x24/0x1e0 [ 16.680295] ret_from_fork+0x10/0x20 [ 16.696369] Code: 927cec03 cb0e0021 8b0e0042 a9411c26 (a900340c) [ 16.723106] ---[ end trace 0000000000000000 ]--- [ 16.752866] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 16.792556] Kernel Offset: 0x3396ea200000 from 0xffff8000800000 ---truncated---

Memory leak in icmp6 implementation in Linux Kernel 5.13+ allows a remote attacker to DoS a host by making it go out-of-memory via icmp6 packets of type 130 or 131. We recommend upgrading past commit 2d3916f3189172d5c69d33065c3c21119fe539fc.