A vulnerability was found in TRENDnet TEW-815DAP 1.0.2.0. It has been classified as critical. This affects the function do_setNTP of the component POST Request Handler. The manipulation of the argument NtpDstStart/NtpDstEnd leads to command injection. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used. The associated identifier of this vulnerability is VDB-252123. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the IP Address in Add Virtual Server.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the action set_sta_enrollee_pin_5g and the key wps_sta_enrollee_pin.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the UDP Ports To Open in Add Gaming Rule.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication). The command injection exists in the key ip_addr.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the IP Address in Add Gaming Rule.

TRENDnet TEW-827DRU with firmware up to and including 2.04B03 contains a stack-based buffer overflow while returning an error message to the user about failure to resolve a hostname during a ping or traceroute attempt. This allows an authenticated user to execute arbitrary code. The exploit can be exercised on the local intranet or remotely if remote administration is enabled.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the key passwd in Routing RIP Settings.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the Private Port in Add Virtual Server.

A vulnerability, which was classified as critical, has been found in TRENDnet TEW-652BRP 3.04B01. This issue affects some unknown processing of the file get_set.ccp of the component Web Management Interface. The manipulation leads to command injection. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used. The associated identifier of this vulnerability is VDB-219935.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the TCP Ports To Open in Add Gaming Rule.

TRENDnet TEW-827DRU devices through 2.06B04 contain a stack-based buffer overflow in the ssi binary. The overflow allows an authenticated user to execute arbitrary code by POSTing to apply.cgi via the action auto_up_fw (or auto_up_lp) with a sufficiently long update_file_name key.

TRENDnet TEW-827DRU devices through 2.06B04 contain a stack-based buffer overflow in the ssi binary. The overflow allows an authenticated user to execute arbitrary code by POSTing to apply.cgi via the action set_sta_enrollee_pin_wifi1 (or set_sta_enrollee_pin_wifi0) with a sufficiently long wps_sta_enrollee_pin key.

TRENDnet TEW-827DRU devices through 2.06B04 contain a stack-based buffer overflow in the ssi binary. The overflow allows an authenticated user to execute arbitrary code by POSTing to apply.cgi via the action st_dev_connect, st_dev_disconnect, or st_dev_rconnect with a sufficiently long wan_type key.

TRENDnet TEW-827DRU devices through 2.06B04 contain a stack-based buffer overflow in the ssi binary. The overflow allows an authenticated user to execute arbitrary code by POSTing to apply.cgi via the action wifi_captive_portal_login with a sufficiently long REMOTE_ADDR key.

TRENDnet TEW-827DRU devices through 2.06B04 contain a stack-based buffer overflow in the ssi binary. The overflow allows an authenticated user to execute arbitrary code by POSTing to apply.cgi via the action kick_ban_wifi_mac_allow with a sufficiently long qcawifi.wifi0_vap0.maclist key.

TRENDnet WiFi Baby Cam TV-IP743SIC has a password of admin for the backdoor root account.

Stack-based buffer overflow in the UltraMJCam ActiveX Control in TRENDnet SecurView TV-IP121WN Wireless Internet Camera allows remote attackers to execute arbitrary code via a long string to the OpenFileDlg method.

apply.cgi on the TRENDnet TEW-632BRP 1.010B32 router has a buffer overflow via long strings to the SOAPACTION:HNAP1 interface.

An issue was discovered on TRENDnet TEW-651BR 2.04B1, TEW-652BRP 3.04b01, and TEW-652BRU 1.00b12 devices. A buffer overflow occurs through the get_set.ccp ccp_act parameter.

Buffer overflow in video.cgi on TRENDnet TV-IP110WN V1.2.2 build 68, V1.2.2.65, and V1.2.2 build 64 and TV-IP121WN V1.2.2 build 28 devices allows attackers to hijack the control flow to any attacker-specified location by crafting a POST request payload (without authentication).

Buffer overflow in network.cgi on TRENDnet TV-IP110WN V1.2.2 build 68, V1.2.2.65, and V1.2.2 build 64 and TV-IP121WN V1.2.2 build 28 devices allows attackers to hijack the control flow to any attacker-specified location by crafting a POST request payload (without authentication).

A vulnerability, which was classified as critical, was found in TRENDnet TEW-811DRU 1.0.10.0. This affects an unknown part of the file wan.asp of the component Web Management Interface. The manipulation leads to memory corruption. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used. The identifier VDB-220017 was assigned to this vulnerability.

A vulnerability was found in TRENDnet TEW-652BRP 3.04B01. It has been declared as critical. This vulnerability affects unknown code of the file cfg_op.ccp of the component Web Service. The manipulation leads to memory corruption. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. VDB-219958 is the identifier assigned to this vulnerability.

Stack-based buffer overflow in UltraCamLib in the UltraCam ActiveX Control (UltraCamX.ocx) for the TRENDnet SecurView camera TV-IP422WN allows remote attackers to execute arbitrary code via a long string to the (1) CGI_ParamSet, (2) OpenFileDlg, (3) SnapFileName, (4) Password, (5) SetCGIAPNAME, (6) AccountCode, or (7) RemoteHost function.

A vulnerability has been found in TRENDnet TEW-811DRU 1.0.10.0 and classified as critical. Affected by this vulnerability is an unknown functionality of the file /wireless/security.asp of the component httpd. The manipulation leads to memory corruption. The attack can be launched remotely. The exploit has been disclosed to the public and may be used. The identifier VDB-219937 was assigned to this vulnerability.

Buffer overflow in Broadcom ACSD allows remote attackers to execute arbitrary code via a long string to TCP port 5916. This component is used on routers of multiple vendors including ASUS RT-AC66U and TRENDnet TEW-812DRU.

An issue was discovered on Vera VeraEdge 1.7.19 and Veralite 1.7.481 devices. The device provides UPnP services that are available on port 3480 and can also be accessed via port 80 using the url "/port_3480". It seems that the UPnP services provide "request_image" as one of the service actions for a normal user to retrieve an image from a camera that is controlled by the controller. It seems that the "res" (resolution) parameter passed in the query string is not sanitized and is stored on the stack which allows an attacker to overflow the buffer. The function "LU::Generic_IP_Camera_Manager::REQ_Image" is activated when the lu_request_image is passed as the "id" parameter in the query string. This function then calls "LU::Generic_IP_Camera_Manager::GetUrlFromArguments". This function retrieves all the parameters passed in the query string including "res" and then uses the value passed in it to fill up buffer using the sprintf function. However, the function in this case lacks a simple length check and as a result an attacker who is able to send more than 184 characters can easily overflow the values stored on the stack including the $RA value and thus execute code on the device.

An issue was discovered on Vera VeraEdge 1.7.19 and Veralite 1.7.481 devices. The device provides UPnP services that are available on port 3480 and can also be accessed via port 80 using the url "/port_3480". It seems that the UPnP services provide "request_image" as one of the service actions for a normal user to retrieve an image from a camera that is controlled by the controller. It seems that the "URL" parameter passed in the query string is not sanitized and is stored on the stack which allows an attacker to overflow the buffer. The function "LU::Generic_IP_Camera_Manager::REQ_Image" is activated when the lu_request_image is passed as the "id" parameter in query string. This function then calls "LU::Generic_IP_Camera_Manager::GetUrlFromArguments" and passes a "pointer" to the function where it will be allowed to store the value from the URL parameter. This pointer is passed as the second parameter $a2 to the function "LU::Generic_IP_Camera_Manager::GetUrlFromArguments". However, neither the callee or the caller in this case performs a simple length check and as a result an attacker who is able to send more than 1336 characters can easily overflow the values stored on the stack including the $RA value and thus execute code on the device.

Remote code execution can occur in Asterisk Open Source 13.x before 13.14.1 and 14.x before 14.3.1 and Certified Asterisk 13.13 before 13.13-cert3 because of a buffer overflow in a CDR user field, related to X-ClientCode in chan_sip, the CDR dialplan function, and the AMI Monitor action.

spice versions though 0.13 are vulnerable to out-of-bounds memory access when processing specially crafted messages from authenticated attacker to the spice server resulting into crash and/or server memory leak.

Buffer overflow in SYS.DBMS_DRS in Oracle Database 9.2.0.7 and 10.1.0.4 allows remote authenticated users to cause a denial of service (crash) or execute arbitrary code via the GET_PROPERTY function in SYS.DBMS_DRS, aka DB03.

Multiple buffer overflows in the ctl_put* functions in NTP before 4.2.8p10 and 4.3.x before 4.3.94 allow remote authenticated users to have unspecified impact via a long variable.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

Apache PLC4X - PLC4C (Only the C language implementation was effected) was vulnerable to an unsigned integer underflow flaw inside the tcp transport. Users should update to 0.9.1, which addresses this issue. However, in order to exploit this vulnerability, a user would have to actively connect to a mallicious device which could send a response with invalid content. Currently we consider the probability of this being exploited as quite minimal, however this could change in the future, especially with the industrial networks growing more and more together.

A vulnerability in Common Internet Filesystem (CIFS) code in the Clientless SSL VPN functionality of Cisco ASA Software, Major Releases 9.0-9.6, could allow an authenticated, remote attacker to cause a heap overflow. The vulnerability is due to insufficient validation of user supplied input. An attacker could exploit this vulnerability by sending a crafted URL to the affected system. An exploit could allow the remote attacker to cause a reload of the affected system or potentially execute code. Note: Only traffic directed to the affected system can be used to exploit this vulnerability. This vulnerability affects systems configured in routed firewall mode only and in single or multiple context mode. This vulnerability can be triggered by IPv4 or IPv6 traffic. A valid TCP connection is needed to perform the attack. The attacker needs to have valid credentials to log in to the Clientless SSL VPN portal. Vulnerable Cisco ASA Software running on the following products may be affected by this vulnerability: Cisco ASA 5500 Series Adaptive Security Appliances, Cisco ASA 5500-X Series Next-Generation Firewalls, Cisco Adaptive Security Virtual Appliance (ASAv), Cisco ASA for Firepower 9300 Series, Cisco ASA for Firepower 4100 Series. Cisco Bug IDs: CSCvc23838.

A stack buffer overflow flaw was found in the Quick Emulator (QEMU) before 2.9 built with the Network Block Device (NBD) client support. The flaw could occur while processing server's response to a 'NBD_OPT_LIST' request. A malicious NBD server could use this issue to crash a remote NBD client resulting in DoS or potentially execute arbitrary code on client host with privileges of the QEMU process.

HP Color LaserJet Pro M280-M281 Multifunction Printer series (before v. 20190419), HP LaserJet Pro MFP M28-M31 Printer series (before v. 20190426) may have embedded web server attributes which may be potentially vulnerable to Buffer Overflow.

A buffer overflow vulnerability in "Add command" functionality exists in Flexense SyncBreeze Enterprise <= 10.3.14. The vulnerability can be triggered by an authenticated attacker who submits more than 5000 characters as the command name. It will cause termination of the SyncBreeze Enterprise server and possibly remote command execution with SYSTEM privilege.

Vyper is a Pythonic Smart Contract Language for the EVM. In affected versions when performing a function call inside a literal struct, there is a memory corruption issue that occurs because of an incorrect pointer to the the top of the stack. This issue has been resolved in version 0.3.0.

A Buffer Overflow issue was discovered in Asterisk Open Source 13 before 13.18.1, 14 before 14.7.1, and 15 before 15.1.1 and Certified Asterisk 13.13 before 13.13-cert7. No size checking is done when setting the user field for Party B on a CDR. Thus, it is possible for someone to use an arbitrarily large string and write past the end of the user field storage buffer. NOTE: this is different from CVE-2017-7617, which was only about the Party A buffer.

Buffer overflow in certain client utilities in OpenAFS before 1.6.2 allows remote authenticated users to cause a denial of service (crash) and possibly execute arbitrary code via a long fileserver ACL entry.

Stack-based buffer overflow in the receive_tcppacket function in net_packet.c in tinc before 1.0.21 and 1.1 before 1.1pre7 allows remote authenticated peers to cause a denial of service (crash) or possibly execute arbitrary code via a large TCP packet.

Stack-based buffer overflow in the acl_get function in Oracle MySQL 5.5.19 and other versions through 5.5.28, and 5.1.53 and other versions through 5.1.66, and MariaDB 5.5.2.x before 5.5.28a, 5.3.x before 5.3.11, 5.2.x before 5.2.13 and 5.1.x before 5.1.66, allows remote authenticated users to execute arbitrary code via a long argument to the GRANT FILE command.

Heap-based buffer overflow in the substr function in parsing.c in cgit 0.9.0.3 and earlier allows remote authenticated users to cause a denial of service (crash) and possibly execute arbitrary code via an empty username in the "Author" field in a commit.

On Insteon Hub 2245-222 devices with firmware version 1012, specially crafted replies received from the PubNub service can cause buffer overflows on a global section overwriting arbitrary data. An attacker should impersonate PubNub and answer an HTTPS GET request to trigger this vulnerability. A strcpy overflows the buffer insteon_pubnub.channel_ad_r, which has a size of 16 bytes. An attacker can send an arbitrarily long "ad_r" parameter in order to exploit this vulnerability.